International Journal of Esthetic Dentistry (DE), 1/2024
Clinical ResearchPagine 46-59, Lingua: TedescoPitta, João / Romandini, Pierluigi / Cantarella, Josef / Kraljevic, Iris / Mojon, Philippe / Magne, Pascal / Magne, Michel / Sailer, IrenaEine retrospektive Studie mit bis zu 27 Jahren NachbeobachtungZiel: In dieser retrospektiven Studie sollte die (technische und biologische) Langzeitbewährung ausgedehnter keramischer Oberkieferfrontzahnveneers mit einer inzisalen Dicke von mehr als 2 mm untersucht werden.
Material und Methoden: Patienten, die zwischen 1990 und 2003 an der Universitätszahnklinik Genf von demselben Zahnarzt mit ausgedehnten Keramikveneers versorgt worden waren, wurden zu einer Nachuntersuchung eingeladen. Von den 37 identifizierten Patienten erklärten sich zehn Patienten mit 50 Veneers zu der Nachuntersuchung bereit und wurden inkludiert. Die Überlebensraten sowie die technischen und biologischen Ergebnisse wurden durch eine klinische Untersuchung bestimmt (anhand der modifizierten United States Public Health Services-Kriterien). Zusätzlich wurden die Patientenakten ausgewertet, um die Patientendaten und alle Komplikationsereignisse zu erfassen. Schließlich wurden Patient-R eported Outcomes (PRO) zu den Aspekten Ästhetik, Funktion und Phonetik, Kaufunktion, Zahnempfindlichkeit und Bereitschaft zu einer Ersatzversorgung im Fall eines Restaurationsversagens mithilfe visueller Analogskalen erhoben. Die Daten wurden deskriptiv ausgewertet. Die Analyse des Restaurationsüberlebens und der Komplikationsereignisse erfolgte mittels Kaplan-Meier-Schätzer.
Ergebnisse: Die Überlebensrate der Veneers betrug 96 % nach im Mittel 20,7 ± 3,7 Jahren in Funktion. Die Rate technischer Komplikationen lag bei 30 %. Diese Komplikationen bestanden in zwei Veneerverlusten, neun reparablen Frakturen, drei Rissbildungen und einer Veneerverlagerung durch Zahnunfall. Es fanden sich weder über Kreideflecken hinausgehende Kariesläsionen noch endodontische Komplikationen dokumentiert. Die PRO bezüglich Zufriedenheit mit der Ästhetik und der Phonetik waren sehr gut.
Schlussfolgerungen: Im Rahmen dieser retrospektiven Studie erwiesen sich ausgedehnte Keramikveneers, gemessen an den klinischen Ergebnissen und der Patientenzufriedenheit, als langfristig erfolgreiche Versorgungsmöglichkeit.
Parole chiave: adhäsive Zahnmedizin, Ästhetik, Keramik, Prothetik, restaurative Zahnmedizin, Veneers
International Journal of Esthetic Dentistry (EN), 1/2024
Clinical ResearchPubMed ID (PMID): 38284943Pagine 46-58, Lingua: InglesePitta, João / Romandini, Pierluigi / Cantarella, Josef / Kraljevic, Iris / Mojon, Philippe / Magne, Pascal / Magne, Michel / Sailer, IrenaA retrospective study with an up to 27-year follow-upAim: The aim of the present retrospective study was to evaluate the long-term results, including technical and biologic outcomes, of maxillary extended porcelain veneers with an incisal edge thickness above 2 mm.
Materials and methods: Patients treated with extended porcelain veneers performed by a single clinician at University of Geneva between 1990 and 2003 were identified and invited to an examination. Of the 37 identified patients, 10 patients with 50 veneers agreed to be examined and were included. A clinical examination was performed to assess survival rates as well as technical and biologic outcomes (modified United States Public Health Services criteria). Patient records were also reviewed to retrieve patient and reconstruction data and every complication event. Patient-reported outcome measures (PROMs) were evaluated using a visual analog scale to measure esthetic satisfaction, functional and phonetic comfort, masticatory improvement, tooth sensitivity, and acceptance of restoration replacement in case of failure. Data were descriptively analyzed, and Kaplan-Meier survival estimators were computed for survival rates and complication events.
Results: The survival rate of the veneers was 96% after a mean follow-up of 20.7 ± 3.7 years in function. The technical complication rate amounted to 30%, including two failures, nine repairable fractures, three cracks, and one displacement due to trauma. No cavitated caries lesions or endodontic complications were registered. PROMs were very high for esthetic satisfaction and phonetic comfort.
Conclusions: Within the limitations of the present retrospective study, extended porcelain veneers appear to be a successful long-term treatment option in terms of clinical outcomes and patient satisfaction.
Parole chiave: adhesive dentistry, esthetics, ceramics, prosthodontics, restorative dentistry, veneers
The Journal of Adhesive Dentistry, 1/2023
Open access Solo onlineResearchDOI: 10.3290/j.jad.b4051477, PubMed ID (PMID): 3709705525. apr 2023,Pagine 99-106, Lingua: IngleseMagne, Pascal / Milani, TabanPurpose: To assess the mechanical performance and enamel-crack propensity of large MOD composite-resin restorations on maxillary molars with severely undermined cusps.
Materials and Methods: Thirty-six extracted maxillary third molars (n = 12) received a standardized slot-type MOD preparation (5-mm depth by 5-mm bucco-palatal width) with severe undercuts, leaving unsupported buccal and lingual enamel cusps. A short-fiber reinforced composite resin base (SFRC, everX Flow, GC) was used for both the experimental direct approach and semi-direct CAD/CAM inlays (Cerasmart 270, GC). In the control group using a direct approach, Gradia Direct (GC) composite resin was used alone without SFRC. Optibond FL (Kerr) adhesive was used in all three groups (also for the immediate dentin sealing of inlays). Artificial masticatory forces were simulated under water using closed-loop servo-hydraulics (MTS Acumen 3). Each specimen was mounted at a 30-degree angle and positioned so that a cylindrical antagonistic cusp (actuator) contacted the internal palatal cusp slope of the restoration. Cyclic loading was applied at a frequency of 5 Hz, starting with a load of 200 N, increasing by 100 N every 2000 cycles. Samples were loaded until fracture and the number of endured cycles and failure modes of each specimen was recorded. Each sample was also evaluated for crack propensity during the experiment and for final failure mode (reparable failures above the CEJ [cementoenamel junction] vs irreparable failures below the CEJ).
Results: Shrinkage-induced cracks (>3 mm) were found in most specimens for both direct groups (66% to 83%) but not with inlays. The survival of inlays with a SFRC base was superior to that of the direct SFRC restorations and Gradia Direct (control) restorations (Kaplan-Meier survival analysis and post-hoc log-rank test p < 0.000). The direct control group without SFRC exhibited not only the poorest survival but also 100% catastrophic failure (vs 42% and 17% for SFRC direct and SFRC inlays, respectively).
Conclusion: Large MOD restorations with severely undermined cusps were most favorably restored with an SFRC base and a CAD/CAM inlay, yielding the highest survival rate, more reparable failures and absence of shrinkage-induced cracks. When a low-cost restoration must be chosen, the SFRC base will significantly improve the performance and failure mode of directly layered restorations.
Parole chiave: short-fiber reinforced composite, composite resin, CAD/CAM, fatigue resistance, crack propensity, undermined cusps, shrinkage stress
International Journal of Esthetic Dentistry (EN), 1/2023
Clinical ResearchPubMed ID (PMID): 36734423Pagine 26-37, Lingua: IngleseLemos Mori Ubaldini, Adriana / Chmielewska, Maja / Baesso, Mauro Luciano / Haghparast, Hadjir / Magne, PascalPurpose: The present study aimed to assess fatigue resistance and color modifications of endodontically treated incisors (ETIs) submitted to internal bleaching and restored using three different techniques.
Materials and methods: Forty-five maxillary central incisors received endodontic treatment and were internally bleached. After the completion of bleaching, the ETIs were divided into three groups (n = 15) according to the different restoration procedures: 1) glass-ionomer cement base covered with composite resin (GI); 2) short fiber-reinforced composite resin base with composite resin (SF); 3) composite resin restoration over a fiberglass post (FP). Specimens were subjected to accelerated fatigue testing: frequency of 5 Hz, beginning with a load of 100 N for 5000 cycles and a 25-N load increase applied every 1700 cycles until a load of 1200 N was reached. Samples were loaded until fracture. The Kaplan-Meier survival analysis with the log-rank post hoc test were performed (α = 0.05). Tooth color was measured 4 weeks after the bleaching treatment and again after the final restoration procedure using a spectrophotometer and the Commission Internationale de l’Eclairage (CIE) L*a*b* system. L* values of the specimens were analyzed using the Shapiro-Wilk and paired sample t tests (α = 0.05).
Results: All groups showed similar survival mean cycles until failure (P = 0.332) and presented a major number of nonrestorable failures. The GI group presented the lowest number of nonrepairable fractures (GI = 68%, SF = 79%, FP = 86%) and showed the most stable L* value (P = 0.987).
Conclusions: The fatigue survival of internally bleached ETIs was not affected by the restorative technique utilized. Retaining the glass-ionomer base and covering the surface with composite resin should provide optimal color stability.
International Journal of Esthetic Dentistry (DE), 1/2023
Clinical ResearchPagine 24-36, Lingua: TedescoLemos Mori Ubaldini, Adriana / Chmielewska, Maja / Baesso, Mauro Luciano / Haghparast, Hadjir / Magne, PascalZiel: In der vorliegenden Studie wurden die Ermüdungsbeständigkeit und Farbstabilität endodontisch behandelter Schneidezähne untersucht, die nach internem Zahnbleaching mit drei verschiedenen Techniken restauriert worden waren.
Material und Methoden: Insgesamt 45 obere zentrale Schneidezähne wurden endodontisch behandelt und erhielten ein internes Bleaching. Nach Abschluss des Bleachings wurden die Zähne drei Gruppen (n = 15) mit jeweils unterschiedlicher Restaurationstechnik zugeordnet: 1. Unterfüllung aus Glasionomerzement bedeckt mit einem Komposit (Gruppe GI), 2. Unterfüllung aus kurzfaserverstärktem Komposit bedeckt mit einem Komposit (Gruppe KF), 3. Kompositrestauration über einem Glasfaserstift (Gruppe FS). Die Proben durchliefen einem beschleunigten Ermüdungstest mit einer Lastfrequenz von 5 Hz, beginnend mit einer Last von 100 N für 5.000 Zyklen und anschließenden Lastinkrementen um 25 N für jeweils 1.700 Zyklen, bis eine Last von 1.200 N erreicht war. Die Proben wurden bis zum Bruch belastet und die Daten mittels Kaplan-Meier-Schätzer und Logrank-Post-hoc-Test ausgewertet (α = 0,05). Die Zahnfarbe wurde vier Wochen nach dem Bleaching und nochmals nach Abschluss der Restaurationstechnik bestimmt, und zwar mithilfe eines Spektralfotometers im CIEL*a*b*-Farbraum. Für die Auswertung wurde der L*-Wert der Proben mit dem Shapiro-Wilk- und dem gepaarten t-Test analysiert (α = 0,05).
Ergebnisse: Die Proben aller drei Gruppen überlebten eine ähnliche mittlere Anzahl an Zyklen bis zum Versagen (p = 0,332) und zeigten eine große Zahl nicht restaurierbarer Frakturen. In der GI-Gruppe fanden sich die geringste Zahl irreparabler Brüche (GI = 68 %, SF = 79 %, FP = 86 %) und der stabilste L*-Wert (p = 0,987).
Schlussfolgerungen: Das Ermüdungsüberleben nach internem Bleaching endodontisch behandelter Schneidezähne wurde nicht vom Restaurationstyp beeinflusst. Die Glasionomerzement-Unterfüllung zu behalten und an der Oberfläche mit einem Komposit zu bedecken, sollte zu einer optimalen Farbstabilität führen.
International Journal of Periodontics & Restorative Dentistry, 4/2022
DOI: 10.11607/prd.5736Pagine 459-469, Lingua: IngleseRodríguez-Ivich, Jair / Razaghy, Mehrdad / Henriques, Bruno / Magne, PascalThis study evaluates the fatigue resistance and failure mode of CAD/CAM composite resin and lithium disilicate-bonded screw-retained incisor crowns with long and short titanium bases. Sixty CAD/CAM implant restorations were fabricated using lithium disilicate (IPS e.max CAD, Ivoclar Vivadent) and composite resin (Block HC, Shofu). The central incisor crowns were bonded to a prefabricated titanium base 6 mm tall (groups: Emax6 and Shofu6; n = 15 each) or a modified abutment 4 mm tall (groups: Emax4 and Shofu4; n = 15 each). The intaglio surface of the restorations was conditioned according to the material and bonded to the titanium abutments/bases using dual-cure cement. All assembled crowns were torqued onto implants and subjected to cyclic isometric loading at the incisal edge along the implant axis. Samples were loaded until fracture. Groups were compared using Kaplan-Meier survival analysis (log rank test at P = .05). The number of mean survived cycles differed significantly, with Emax6 and Emax4 at 48,448 and 43,727 cycles, respectively, and Shofu6 and Shofu4 at 44,124 and 37,620 cycles, respectively. Post hoc tests showed similar fatigue resistance for Emax6, Emax4, and Shofu6. Shofu4 was less resistant than all other groups (P < .03). All restorations survived significantly above physiologic load limits. Lithium disilicate screw-retained incisor crowns can be used with long and short titanium bases, while it is recommended to keep a long titanium base for screw-retained composite resin crowns. The composite resin material required the full height of the abutment for optimal strength but may offer enhanced shock absorption and wear-friendliness when considering function and antagonistic wear.
International Journal of Esthetic Dentistry (EN), 4/2021
PubMed ID (PMID): 34694078Pagine 534-552, Lingua: Inglesede Carvalho, Marco Aurélio / Lazari-Carvalho, Priscilla Cardoso / Del Bel Cury, Altair A. / Magne, PascalPurpose: The present study aimed to investigate the resistance and failure mode of broken-down endodontically treated incisors without ferrule restored with CAD/CAM endocrowns.
Materials and methods: Endodontically treated bovine incisors (N = 30) without ferrule were divided into two groups and restored with two types of CAD/CAM endocrowns: lithium disilicate (Eld) or resin nanoceramics (Erc). The preparations included a 4-mm–deep ‘internal ferrule’ and immediate dentin sealing. The samples were subjected to accelerated fatigue testing. Cyclic isometric loading was applied to the incisal edge at a 30-degree angle at a frequency of 5 Hz, beginning with a load of 100 N (5,000 cycles). A 100 N load increase was applied every 15,000 cycles. Specimens were loaded until failure or to a maximum of 140,000 cycles. Previously published data from the same authors regarding lithium disilicate crowns over post-and-core buildups without ferrule (NfPf), core buildups without post without ferrule (NfNpFR), and with a 2-mm ferrule (FNp) using the same experimental setup were included for comparison. Groups were compared using the Kaplan Meier survival analysis for cycles (log rank pairwise post hoc test comparisons at P = 0.05) and Life Table survival analysis for load at failure, followed by the Wilcoxon pairwise comparison at P = 0.05.
Results: All specimens failed before 140,000 load cycles. There was no statistically significant difference between the endocrown materials (Eld: 53,448 mean endured cycles; Erc: 52,397 mean endured cycles; P = 0.844). Endocrowns outperformed the group with lithium disilicate crowns on incisors without ferrule and post-and-core buildup (NfPf with mean endured 35,025 cycles), showed no statistical difference compared with the group with no-post fiber-reinforced composite resin core buildup (NfNpFR with 45,557 mean endured cycles), and had a lower survival rate compared with the group with ferrule (FNp with mean endured 73,244 cycles). Endocrowns generated a majority of non-catastrophic failures (with an advantage for Erc), while 100% of catastrophic failures were found in the group with a post.
Conclusions: CAD/CAM endocrowns of nonvital incisors without ferrule improved the resistance and optimized the failure mode when compared with traditional bonded crowns with adhesive post-and-core and no-post buildups.
International Journal of Esthetic Dentistry (DE), 4/2021
Pagine 464-483, Lingua: Tedescode Carvalho, Marco Aurélio / Lazari-Carvalho, Priscilla Cardoso / Del Bel Cury, Altair A. / Magne, PascalZiel: Ziel der vorliegenden Studie war es, die Ermüdungsbeständigkeit endodontisch behandelter Schneidezähne (EBS) mit CAD/CAM-Endokronen ohne zirkuläre Umfassung (ferrule) sowie die Bruchformen nach Fraktur zu untersuchen.
Material und Methode: Wurzelbehandelte Rinderzähne (n = 30) wurden in zwei Gruppen geteilt und mit CAD/CAM-Endokronen ohne zirkuläre Umfassung aus zwei verschiedenen Materialien restauriert: Lithiumdisilikat (LD) und Nanokomposit (NK). Die Präparation wurde mit 4 mm tiefer „interner Umfassung” und sofortiger Dentinversiegelung durchgeführt. Die Proben durchliefen folgenden Ermüdungstest: Die Schneidekanten wurden zyklischen isometrischen Belastungen im Winkel von 30° und mit einer Frequenz von 5 H z ausgesetzt, die bei einer Kraft von 100 N für 5000 Zyklen begann und anschließend alle 15000 Zyklen um 100 N gesteigert wurde. Der Ermüdungstest wurde bis zum Bruch oder maximal für 140000 Zyklen fortgesetzt. Früher publizierte Daten derselben Autoren zu Lithiumdisilikat-Kronen (1) ohne zirkuläre Umfassung mit Stift (oUmS), (2) ohne zirkuläre Umfassung, ohne Stift mit kurzfaserverstärktem Kompositaufbau (oUoSfv) und (3) mit 2 mm hoher zirkulärer Umfassung ohne Stift (mUoS), die mit der gleichen Versuchsanordnung erhoben worden waren, wurden zu Vergleichszwecken mit eingeschlossen. Die Gruppenvergleiche erfolgten mittels Kaplan-Meier-Schätzer für die Belastungszyklen (mit Post-hoc-Logrank-Test mit p = 0,05) und Sterbetafelanalyse für die Bruchlast, gefolgt von einem Wilcoxon-Paarvergleich (p = 0,05).
Ergebnisse: Alle Proben brachen vor Erreichen von 140000 Lastzyklen. Es gab keine statistisch signifikanten Unterschiede zwischen den Endokronenmaterialien (mittlere durchlaufene Anzahl Lastzyklen: LD: 53448, NK: 52397, p = 0,844). Die LD- und NK-Endokronen bewährten sich besser als die Lithiumdisilikat-Kronen ohne zirkuläre Umfassung mit Stiftaufbau (oUmS) (die durchschnittlich 35025 Lastzyklen erreichten), zeigten keinen statistisch signifikanten Unterschied zur Gruppe mit faserverstärkter Aufbaufüllung ohne Wurzelstift und ohne zirkuläre Umfassung (oUoSfv) (durchschnittlich 45557 erreichte Zyklen) und hatten eine geringere Überlebensrate als die Gruppe mit zirkulärer Umfassung ohne Stift (mUoS) (durchschnittlich 73244 erreichte Zyklen). LD- und NK-Endokronen führten in der Mehrzahl zu nicht fatalen Frakturen (mit einem Vorteil bei der NK-Gruppe), während in der Gruppe mit Wurzelstift zu 100 % fatale Frakturen auftraten.
Schlussfolgerung: Im Vergleich mit adhäsiv befestigten klassischen Kronen mit Stiftaufbau verbessern CAD/CAM-Endokronen ohne zirkuläre Umfassung auf avitalen Schneidezähnen die Frakturbeständigkeit und die Bruchform.
International Journal of Periodontics & Restorative Dentistry, 1/2021
Pagine 113-119a, Lingua: IngleseMargossian, Patrice / Laborde, Gilles / Koubi, Stefen / Tardivo, Delphine / Magne, PascalAlthough it is generally accepted that a prosthetic restoration must take into account the gingiva, smile, and patient’s face, it is often difficult to determine precisely what facial references must be considered. The purpose of this study was to determine the correct vertical and horizontal facial reference planes in esthetic prosthetic treatment. Using photographic analysis of 160 individuals, the different facial reference planes (interpupillary, intermeatic, intercommissural, and incisal edge lines; facial midline; and Camper and Frankfort planes) were compared to the ideal prosthetic reconstruction axis. Additional measurements, including the human eye’s ability to perceive parallelism, were recorded. Most participants (64%) exhibited facial asymmetry. Asymmetry was horizontal (difference between widths of the right and left sides; 52.4%), vertical (difference between heights of the right and left sides; 6.9%), or mixed (4.7%). The interpupillary line is the main horizontal reference in 88.4% of situations, with the intercommissural line the second most important. In the profile view, the horizontal plane was on average 6.5 degrees above the Camper plane and 9 degrees below the Frankfort plane. The human eye’s ability to perceive parallelism between two lines was found to be limited to differences of approximately 1 degree. During anterior tooth reconstruction, it is necessary to take into account the right horizontal and vertical esthetic references. Knowledge of the biometric facial parameters in natural dentition is necessary to define the right reconstruction axes based on the facial symmetry or asymmetry.
International Journal of Esthetic Dentistry (EN), 3/2018
PubMed ID (PMID): 30073216Pagine 318-332, Lingua: IngleseMagne, Pascal / Razaghy, Mehrdad / Carvalho, Marco Aurelio / Soares, Luciana MaraPurpose: To evaluate in vitro the vertical seating of computer-assisted design/computer-assisted manufacturing (CAD/CAM) composite resin inlays, onlays, and overlays luted with two different composite resins.
Materials and methods: Sixty plastic typodont molars were prepared for medium-sized MOD inlays, anatomic onlays, and flat overlays (n = 20); 3-mm thick at the central groove with similar morphology (Cerec biogeneric copy). Restorations were milled using Lava Ultimate blocks, and included standardized hemispherical occlusal concavity for seating measurements with an electromechanic system (force = 30 N). Restorations were luted either with preheated composite resin (Filtek Z100) or dual-cure resin cement (RelyX Ultimate). Seating of restorations was first evaluated at try-in (baseline). Seating was reevaluated after airborne-particle abrasion (Step 1), after seating with luting agent (Step 2), and after light polymerization (Step 3). The Friedman test followed by the Wilcoxon post hoc test were used to compare the seating among steps, and the Kruskal-Wallis test followed by the Mann-Whitney post hoc test were used to compare the seating between luting agents at P 0.05.
Results: Seating differences varied significantly from baseline (P 0.0125). All restorations seated 3.85 µm (inlays) to 5.45 µm (onlays) deeper after airborne-particle abrasion (Step 1) (P 0.007). Except for cement-luted inlays, the try-in position (±1 µm) was recovered following unpolymerized luting (Step 2). After polymerization (Step 3), onlays and overlays seated 2.9 to 3.9 µm deeper than during try-in (baseline) using Z100 (P 0.005), and 7.0 to 7.3 µm deeper using RelyX (P = 0.005). Inlays luted with RelyX seated higher than during try-in (baseline), exactly 7.9 µm after Step 2 (P = 0.005), and 7.7 µm after Step 3 (P = 0.008). Luting with Z100 sustained the seating of inlays with no statistical difference when compared to baseline (P = 0.157).
Conclusion: Airborne-particle abrasion significantly deepens the seating of CAD/CAM composite resin restorations, but the presence of unpolymerized restorative composite resin luting agent perfectly compensates for this discrepancy. Following polymerization, onlays and overlays seat deeper compared to inlays, especially when using RelyX. The latter, however, resulted in a slightly higher seating of inlays.
Clinical significance: With the least variation compared to baseline seating (try-in), restorative composite resin used as luting agent resulted in the seating of CAD/CAM inlays, onlays, and overlays closer to baseline when compared to dual-cure resin cement.
